How to learn automatic labeling machine maintenance technology? -Automatic labeling machine manufacturer-Online printing labeling machine-Shenzhen Bogao logo
by：Zhongya Packaging 2022-02-03
Nowadays, many factories work with robots, and those who enter the factory are skilled talents. But how can you be more skilled than others? That is, you can repair the broken machines at work, as a labeling machine manufacturer. , How to learn the maintenance technology of automatic labeling machine? It is a job where you have one more skill than others. Now you can cooperate with manufacturers to buy machines and send instructional videos. I will sort out a few common repair methods and share with you. The adjustment of the pressure brush device The center of the mark brush is aligned with the label and the two sides are symmetrical. The marking brush is perpendicular to the surface of the container. The overlap gap of the pressure brush sweeping the container is: a single pressure brush is 10mm-15mm, and a combined pressure brush is 5mm-10mm. The distance between the cleaning brush and the sponge is 1mm~2mm. Adjustment of the pressure bottle head. The pressing head should be 20mm lower when there is no bottle than when there is a bottle. Adjust the center line of the label box, the center axis of the label station is tangent to the label paper, and the center axis of the label is three points into a line. Adjust the tangent of the label to the label paper (0 distance), and then move the label box closer to 1mm～2mm That's it. The gap between the label paper in the label box and the pressing strips on both sides should be between 0.8mm and 1mm. If the gap is too large, the label paper will be shifted in the label box and oblique marks will appear. If the gap is too small, it will cause poor label push. Adjustment of the position of the label-grabbing hooks of the label box: the upper, lower, left and right label-grabbing hooks are on the same vertical plane and evenly work hard on the label paper, so that the label can be grasped smoothly. Adjustment of the label supply roller: When there is no label, the label pressing plate can be pressed to the front end of the label box and the label near the label hook finger cannot be crushed. The adjustment of the marking station The adjustment of the squeegee and the rubber roller: There should be no gap between the squeegee and the rubber roller in the entire length. If there is a gap, the squeegee can be adjusted by adjusting the eccentric bolt. The adjustment of the rubber roller and the standard plate: the standard plate and the rubber roller are only in contact with each other without any pressure. The gap is too large and there is too much glue on the target plate, causing glue rejection. If the gap is too small and the contact is too tight, the glue will be squeezed away, and there is no glue on the half of the target board. Practice has proved that the best gap between the standard plate and the rubber roller is between 0.1mm and 0.2mm. This can be achieved by adjusting the bearing seat at the lower part of the rubber roller, and if necessary, adjust the bearing on the upper part of the rubber roller. The adjustment of the bottle inlet star wheel, the bottle outlet star wheel and the bottle inlet screw rod When adjusting the bottle inlet and outlet star wheel and the bottle inlet screw rod, the press head of the standard machine shall prevail. First, adjust the bottle inlet star wheel. When the bottle pressing head just overwhelms the bottle, adjust the bottle inlet star wheel so that the bottle is in the middle of the star wheel groove. Adjustment of the bottle feeding screw: take the bottle feeding star wheel as the standard. When the bottle is in the middle of the groove of the bottle feeding star wheel, adjust the screw rod so that the bottle inlet side of the screw is close to the bottle without displacement. Adjustment of the bottle-out star wheel: When the bottle pressing head is just raised, adjust the star wheel so that the bottle is in the middle of the groove of the star wheel. Today, the editor summarizes four points of knowledge, which friends in the packaging industry will remember. How to learn the maintenance technology of automatic labeling machine? It's really a relatively practical work technique and work experience. It's not a problem to learn how to raise a salary and get a promotion. We are a professional labeling machine manufacturer to share the knowledge of labeling machine is my happiness, remember to buy a labeling machine to send instructional videos.