How to debug the automatic labeling machine-automatic labeling machine manufacturer-online printing labeling machine-shenzhen bogao logo
by:Zhongya Packaging
2022-05-12
How to debug the labeling machine skills is what we must operate in our daily production, so the editor summarizes it to facilitate users at work and can improve our work efficiency. Now the emergence of fully automatic labeling machines drives the development of related industries. The technology of individualization and automation undoubtedly highlights the charm of the labeling machine. At present, there are more and more types of labeling machines on the market, and the more choices users have, the more picky they are about the products. Good products are also inseparable from the care of users, Bogao logo will teach you how to debug the labeling machine! Now you can test the machine for free. The adjustment of the pressure brush device: the center of the mark brush is aligned with the label and the two sides are symmetrical and perpendicular to the surface of the container. The overlap gap of the pressure brush sweeping the container is: a single pressure brush is 10mm-15mm, and a combined pressure brush is 5mm-10mm. The distance between the cleaning brush and the sponge is 1mm~2mm. The pressing head should be 20mm lower when there is no bottle than when there is a bottle. The adjustment of the label box: the center line of the label box, the center axis of the label station is tangent to the label paper, and the center axis of the label plate forms a line at three points. Adjust until the label plate and the label paper are tangent (0 distance), and then move the label box closer to 1mm ~2mm is fine. The gap between the label paper in the label box and the pressing strips on both sides should be between 0.8mm-1mm, too large a gap will cause the label paper to shift in the label box, and oblique marks will appear; too small a gap will cause poor label push. Adjustment of the position of the label-grabbing hooks of the label box: the upper and lower, left and right label-grabbing hooks are on the same vertical plane and evenly work hard on the label paper, so that the label can be grasped smoothly. The adjustment of the label supply roller: when there is no label, the label pressing plate can be pressed to the front end of the label box and the label near the label hook finger cannot be crushed. Adjustment of the bottle inlet star wheel, bottle outlet star wheel, and bottle inlet screw rod When adjusting the bottle inlet and outlet star wheel and bottle inlet screw rod, the press head of the standard machine shall prevail. Adjustment of the bottle feeding star wheel: When the bottle pressing head just overwhelms the bottle, adjust the bottle feeding star wheel so that the bottle is in the middle of the star wheel groove. Adjustment of the bottle feeding screw: take the bottle feeding star wheel as the standard. When the bottle is in the middle of the groove of the bottle feeding star wheel, adjust the screw rod so that the bottle inlet side of the screw is close to the bottle without displacement. Adjustment of the bottle-out star wheel: When the bottle pressing head is just raised, adjust the star wheel so that the bottle is in the middle of the groove of the star wheel. The adjustment of the standard station: the adjustment of the squeegee and the rubber roller: there should be no gap between the squeegee and the rubber roller in the entire length. If there is a gap, the squeegee can be adjusted by adjusting the eccentric bolt. The adjustment of the rubber roller and the standard plate: the standard plate and the rubber roller are only in contact with each other without any pressure. If the gap is too large, there is too much glue on the target plate, which will cause the glue to be thrown; if the gap is too small and the contact is too tight, the glue will be squeezed away, and there is no glue on the half of the target plate. Practice has proved that the best gap between the standard plate and the rubber roller is between 0.1mm and 0.2mm, which can be achieved by adjusting the bearing seat at the lower part of the rubber roller, and if necessary, adjust the bearing on the upper part of the rubber roller. Have you learned this dry goods knowledge? How to debug the labeling machine skills is over here, I hope you will try more in your work, our company independently develops and produces the labeling machine, so we will share dry goods with you at irregular times Operating knowledge, I hope it will be helpful to you, and also let you understand the advantages of our labeling machine in the market. So now we launch a free trial machine activity, come here to learn more about the activity!
Custom message