Zhuhai Zhongya Technology Co., Ltd.


Full-Auto Slitting Machine Manufacturer in China Since 2009

+ 86-0756 386 7226 

Maintenance tips of labeling machine-industry news

by:Zhongya Packaging      2022-05-25
Labeling machines mainly include: self-adhesive labeling machine, sleeve labeling machine, round bottle labeling machine, beer labeling machine, semi-automatic labeling machine, labeling machine, automatic labeling machine, automatic labeling machine, labeling machine , Automatic labeling machine, hot melt adhesive labeling machine. These products can be pasted on flat surfaces, pasted on one or more sides of packaging, pasted on cylindrical surfaces, pasted on partially or fully covered cylinders, pasted on recesses and corners, etc. If you want the labeling machine to have a longer life, then we Take good care of the labeling machine and pay attention to the maintenance of the labeling machine. Maintenance tips of the labeling machine:      1. Adjustment of the pressure brush device      The center of the label brush is aligned with the label and both sides are symmetrical. The marking brush is perpendicular to the surface of the container. The overlap gap of the pressure brush sweeping the container is: a single pressure brush is 10mm-15mm, and a combined pressure brush is 5mm-10mm. The distance between the cleaning brush and the sponge is 1mm~2mm. Adjustment of the pressure bottle head. The pressing head should be 20mm lower when there is no bottle than when there is a bottle. 2. Adjust the center line of the label box, the center axis of the label station is tangent to the label paper, and the center axis of the label is three points into a line. Adjust the tangent of the label to the label paper (0 distance), and then move the label box closer to 1mm ~2mm is fine. The gap between the label paper in the label box and the pressing strips on both sides should be between 0.8mm and 1mm. If the gap is too large, the label paper will be shifted in the label box and oblique marks will appear. If the gap is too small, it will cause poor label push. Adjustment of the position of the label-grabbing hooks of the label box: the upper, lower, left and right label-grabbing hooks are on the same vertical plane and evenly work hard on the label paper, so that the label can be grasped smoothly. Adjustment of the label supply roller: When there is no label, the label pressing plate can be pressed to the front end of the label box and the label is installed, the label near the label hook finger cannot be crushed.    3. Adjustment of the bottle inlet star wheel, bottle outlet star wheel, and bottle inlet screw rod      When adjusting the bottle inlet and outlet star wheel and bottle inlet screw rod, the press head of the standard machine shall prevail. First, adjust the bottle inlet star wheel. When the bottle pressing head just overwhelms the bottle, adjust the bottle inlet star wheel so that the bottle is in the middle of the star wheel groove. Adjustment of the bottle feeding screw: Take the bottle feeding star wheel as the standard. When the bottle is in the middle of the groove of the bottle feeding star wheel, adjust the screw rod so that the bottle inlet side of the screw rod is close to the bottle without displacement. Adjustment of the bottle-out star wheel: When the bottle pressing head is just raised, adjust the star wheel so that the bottle is in the middle of the groove of the star wheel.    4. Adjustment of the standard station     Adjustment of the squeegee and the rubber roller: There should be no gap between the squeegee and the rubber roller in the entire length. If there is a gap, the squeegee can be adjusted by adjusting the eccentric bolt. The adjustment of the rubber roller and the standard plate: the standard plate and the rubber roller are only in contact with each other without any pressure. The gap is too large and there is too much glue on the target plate, causing glue rejection. If the gap is too small and the contact is too tight, the glue will be squeezed away, and there is no glue on the half of the target board. Practice has proved that the gap between the standard plate and the rubber roller is between 0.1mm and 0.2mm to be the best. This can be achieved by adjusting the bearing seat at the lower part of the rubber roller, and if necessary, adjust the bearing on the upper part of the rubber roller.
Custom message
Chat Online
Chat Online
Leave Your Message inputting...
Dear customer, there are too many customer inquiries, and it may not be possible to reply you in time. You can contact me on WhatsApp (WhatsApp ID: +86 15013463303 Zhongya), or you can send your contact information or email to my email, I will reply you as soon as I receive the message, my email is lanqiao0560@gmail.com . thanks